Duplex Steel Pipe Fittings
Duplex metal Elbow Pipe Fittings can generally carry out well in environments that reason premature failure of number one solid solution grades. Duplex Steel Long Radius Elbow Pipe Fittings have better resistance to brine than Grade 316, this is a more atomic wide variety 7 improved stainless steel that was advanced to combat common corrosion troubles encountered with the 300 collection untainted sheets of metallic.Duplex steel Tee Pipe Fittings have outstanding high-short-term worker resistance, it becomes brittle if understood for longer durations at temperatures quite 300 degrees Celsius. Duplex steel Reducer Pipe Fittings will solely be corrected by using a complete decision tempering treatment, which isn't used on top of 300 diploma C. The high electricity of Duplex steel Pipe gives up Caps Fittings gives opportunities for lowering each weight and cost as a diluent material is often used, while the low nickel content material of those duplex steel makes them feel solid. Duplex steel reducing Tee Pipe Fittings can not be hardened by way of thermal remedy.
Specification of Pipe Fittings
| Duplex Steel Pipe Fittings Standard | ASTM A815 / ASME SA815 |
|---|---|
| DSS Pipe Fitting Dimensions | ASME/ANSI B16.9, ASME B16.28, MSS-SP-43 |
| Duplex Steel Pipe Fitting Size Range | 1/2” NB to 24″NB in |
| DSS Pipe Fittings Type | Seamless / Welded / Fabricated |
| ASTM A815 Duplex Pipe Fittings Thickness | Sch 5s, Sch 10s, Sch 40s, Sch 80s, Sch 160s, Sch XXS |
| Grades | Duplex S31803, S32205 |
Duplex Steel Pipe Fittings Dimensional Tolerances
| All Fittings | 90°and 45° Ells and Tees | Reducers and Lap Joint Stub | Caps | 180° Returns | Angularity Tol | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Nominal Pipe Plane Size (NPS) | Outside(1) Diameter at Bevel | Inside(1) Diameter at End | Wall(2) Thickness | Centre-to- End Dimension A,B,C,M | Overall Length L | Overall Length E | Centre-to- Centre Dimension O | Back-to- Face Dimension K | Alignment at Ends U | Nominal Pipe SIze | Off Angle Q | Off Angle P |
| 1/2 TO 2-1/2 | +1/16 | ±1/32 | Not less than 87-1/2% of Normal Thickness | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 12 to 4 | 1/32 | 1/16 |
| -1/32 | 5 to 8 | 1/16 | 1/8 | |||||||||
| 3 TO 3-1/2 | ±1/16 | ±1/16 | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 10 to 12 | 3/32 | 3/16 | |
| 4 | ±1/16 | ±1/16 | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 14 to 16 | 3/32 | 1/4 | |
| 5 TO 8 | +1/32 | ±1/16 | ±1/16 | ±1/16 | ±1/4 | ±1/4 | ±1/4 | ±1/32 | 18 to 24 | 1/8 | 3/8 | |
| -1/16 | ||||||||||||
| 10 TO 18 | +1/16 | ±1/8 | ±3/32 | ±3/32 | ±1/4 | ±3/8 | ±1/4 | ±1/16 | All dimensions are in inches | |||
| -1/8 | ||||||||||||
| 20 TO 24 | +1/4 | ±3/32 | ±3/32 | ±3/32 | ±1/4 | ±3/8 | ±1/4 | ±1/16 | ||||
| -3/32 | ||||||||||||
Duplex Steel S31803 Butt Weld Pipe Fittings.
Duplex Steel S31803 Butt Weld Pipe Fittings are majorly composed of chromium, iron, nickel, molybdenum, manganese, silicon, and other required materials. The major selling point of duplex steel is that it is an exceptionally corrosion resistant alloy and can be worked hardened skillfully. Because of its nickel and chromium content, Duplex Steel S31803 has both austenitic and ferritic properties. The majority of the time, duplex steel is tougher than ferritic steel. There are cases of duplex steel having double the strength of austenitic stainless steel.Duplex Steel S31803 Butt Weld Pipe Fittings become brittle and partially or completely loses their ductility at a temperature above 300°C. It is more ductile than ferritic alloys at lower temperatures. It can maintain its usability at about -50°C. Its fabrication requires the use of only stainless steel alloy-specific tools. Although these alloys may be machined, the process is challenging due to their great strength. Welding is possible with duplex stainless steel. All standard welding procedures are usable.
Specification For DSS S31803 Pipe Fittings
| Duplex Steel S31803 Pipe Fittings Standard | ASTM A815 / ASME SA815 |
|---|---|
| DSS S31803 Pipe Fitting Dimensions | ASME/ANSI B16.9, ASME B16.28, MSS-SP-43 |
| Duplex Steel S31803 Pipe Fitting Size Range | 1/2” NB to 24″NB in |
| DSS S31803 Pipe Fittings Type | Seamless / Welded / Fabricated |
| ASTM A815 Duplex S31803 Pipe Fittings Thickness | Sch 5s, Sch 10s, Sch 40s, Sch 80s, Sch 160s, Sch XXS |
| Grades | Duplex S31803, S32205 |
Equivalent Grades Of Duplex Steel S31803 Pipe Fittings
| STANDARD | WERKSTOFF NR. | UNS |
| Duplex S31803 | 1.4462 | S31803 |
Duplex Steel S31803 Pipe Fittings Chemical Composition
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N | Fe |
| S31803 | 0.030 max | 2.00 max | 1.00 max | 0.030 max | 0.020 max | 22.0 – 23.0 | 3.0 – 3.5 | 4.50 – 6.50 | 0.14 – 0.20 | 63.72 min |
Duplex Steel S31803 Pipe Fittings Mechanical Properties
| Grades | Density (g/cm 3) | Density (lb/in 3) | Melting Point (°C) | Melting Point (°F) |
| S31803 | 7.805 | 0.285 | 1420 – 1465 | 2588 – 2669 |
Duplex Steel S31803 Pipe Fittings Dimensional Tolerances
| All Fittings | 90°and 45° Ells and Tees | Reducers and Lap Joint Stub | Caps | 180° Returns | Angularity Tol | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Nominal Pipe Plane Size (NPS) | Outside(1) Diameter at Bevel | Inside(1) Diameter at End | Wall(2) Thickness | Centre-to- End Dimension A,B,C,M | Overall Length L | Overall Length E | Centre-to- Centre Dimension O | Back-to- Face Dimension K | Alignment at Ends U | Nominal Pipe SIze | Off Angle Q | Off Angle P |
| 1/2 TO 2-1/2 | +1/16 | ±1/32 | Not less than 87-1/2% of Normal Thickness | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 12 to 4 | 1/32 | 1/16 |
| -1/32 | 5 to 8 | 1/16 | 1/8 | |||||||||
| 3 TO 3-1/2 | ±1/16 | ±1/16 | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 10 to 12 | 3/32 | 3/16 | |
| 4 | ±1/16 | ±1/16 | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 14 to 16 | 3/32 | 1/4 | |
| 5 TO 8 | +1/32 | ±1/16 | ±1/16 | ±1/16 | ±1/4 | ±1/4 | ±1/4 | ±1/32 | 18 to 24 | 1/8 | 3/8 | |
| -1/16 | ||||||||||||
| 10 TO 18 | +1/16 | ±1/8 | ±3/32 | ±3/32 | ±1/4 | ±3/8 | ±1/4 | ±1/16 | All dimensions are in inches | |||
| -1/8 | ||||||||||||
| 20 TO 24 | +1/4 | ±3/32 | ±3/32 | ±3/32 | ±1/4 | ±3/8 | ±1/4 | ±1/16 | ||||
| -3/32 | ||||||||||||
Duplex Steel S32205 Butt Weld Pipe Fittings
Duplex Steel 2205 Butt Weld Pipe Fittings are a ferritic and austenitic alloy due to the presence of chromium and nickel. It is used in applications requiring excellent corrosion resistance and high strength. This grade was developed after many improvements were made to Duplex Steel S31803, and it has more corrosion resistance than the latter. This alloy has lower heat resistance than an alloy of stainless steel grade. It becomes brittle at a high temperature of 300°C. At a low temperature of -50°C, the alloy undergoes embrittlement. As a result, this stainless steel grade is not suited for usage at these temperatures.Duplex Steel 2205 S32205 Butt Weld Pipe Fittings are generally used in Shipbuilding and Marine Industry, such as for Shafts and Propellers, Rudders, Pumps, Shaft Seals, Fasteners and Bolts, Valves, Chemical and Oil Tankers, Instrumentation, etc.
Due to their durability, strength, and corrosion resistance, S32205 duplex stainless steel pipe fittings are highly prized. Applications like pressure vessels, oil and gas exploration, chemical processing, and transportation infrastructure all benefit significantly from these characteristics. Due to the superior weldability of these pipes, piping systems may be built more efficiently and with fewer connections.
Specification For DSS S32205 Pipe Fittings
| Duplex Steel S32205 Pipe Fittings Standard | ASTM A815 / ASME SA815 |
|---|---|
| DSS S32205 Pipe Fitting Dimensions | ASME/ANSI B16.9, ASME B16.28, MSS-SP-43 |
| Duplex Steel S32205 Pipe Fitting Size Range | 1/2” NB to 24″NB in |
| DSS S32205 Pipe Fittings Type | Seamless / Welded / Fabricated |
| ASTM A815 Duplex S32205 Pipe Fittings Thickness | Sch 5s, Sch 10s, Sch 40s, Sch 80s, Sch 160s, Sch XXS |
| Grades | Duplex S32205, S32205 |
Equivalent Grades Of Duplex Steel S32205 Pipe Fittings
| STANDARD | WERKSTOFF NR. | UNS |
| Duplex 2205 | 1.4462 | S32205 |
Duplex Steel S32205 Pipe Fittings Chemical Composition
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N | Fe |
| S32205 | 0.030 max | 2.00 max | 1.00 max | 0.030 max | 0.020 max | 21.0 – 23.0 | 2.50 – 3.50 | 4.50 – 6.50 | 0.8 – 0.20 | 63.54 min |
Duplex Steel S32205 Pipe Fittings Mechanical Properties
| Grades | Density (g/cm 3) | Density (lb/in 3) | Melting Point (°C) | Melting Point (°F) |
| S32205 | 7.805 | 0.285 | 1420 – 1465 | 2588 – 2669 |
Duplex Steel S32205 Pipe Fittings Dimensional Tolerances
| All Fittings | 90°and 45° Ells and Tees | Reducers and Lap Joint Stub | Caps | 180° Returns | Angularity Tol | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Nominal Pipe Plane Size (NPS) | Outside(1) Diameter at Bevel | Inside(1) Diameter at End | Wall(2) Thickness | Centre-to- End Dimension A,B,C,M | Overall Length L | Overall Length E | Centre-to- Centre Dimension O | Back-to- Face Dimension K | Alignment at Ends U | Nominal Pipe SIze | Off Angle Q | Off Angle P |
| 1/2 TO 2-1/2 | +1/16 | ±1/32 | Not less than 87-1/2% of Normal Thickness | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 12 to 4 | 1/32 | 1/16 |
| -1/32 | 5 to 8 | 1/16 | 1/8 | |||||||||
| 3 TO 3-1/2 | ±1/16 | ±1/16 | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 10 to 12 | 3/32 | 3/16 | |
| 4 | ±1/16 | ±1/16 | ±1/16 | ±1/16 | ±1/8 | ±1/4 | ±1/4 | ±1/32 | 14 to 16 | 3/32 | 1/4 | |
| 5 TO 8 | +1/32 | ±1/16 | ±1/16 | ±1/16 | ±1/4 | ±1/4 | ±1/4 | ±1/32 | 18 to 24 | 1/8 | 3/8 | |
| -1/16 | ||||||||||||
| 10 TO 18 | +1/16 | ±1/8 | ±3/32 | ±3/32 | ±1/4 | ±3/8 | ±1/4 | ±1/16 | All dimensions are in inches | |||
| -1/8 | ||||||||||||
| 20 TO 24 | +1/4 | ±3/32 | ±3/32 | ±3/32 | ±1/4 | ±3/8 | ±1/4 | ±1/16 | ||||
| -3/32 | ||||||||||||